High Performance Specialty Chemicals & Services Request a Quote
Print this page

Clean-N-Clear: Interior & Exterior Building Cleaner

  • Clean-N-Clear Removes Type 1 Water Stains/Spots
  • Clean-N-Clear a great building and glass cleaner
  • Clean-N-Clear is Biodegradable
Click image to enlarge
Download TDS:

Environmentally friendly, liquid cleaner for building interiors and exteriors. Safe on all glass surfaces.

Clean-N-Clear is the approved cleaner for LEED Certified Buildings and is Biodegradable and will not harm plants or trees.

Description

NuGeneration Technologies’ Clean-N-Clear is an environmentally friendly, liquid cleaner for building interiors and exteriors. Clean-N-Clear eliminates alkaline residues, exhaust particles, chemical and mineral deposits, water spots and the runoff from brick, concrete, mortar and even rust. Excellent for new building cleanups. Clean-N-Clear is a solvent-free formula.

Characteristics

Clean-N-Clear was formulated to remove Stage 1 water spots from alkaline buildup, hard water, sprinklers, acid rain, and calcium on glass. Clean-N-Clear also removes stains from acid rain, hard water, rust, oxides, dirt, greases, grime, etc. Clean-N-Clear is effective on concrete, brick, granite, glass, ferrous metals, Aluminum, Brass and Copper, and may also be used in floor scrubbers and is excellent at facilitating oil-splitting Clean-N-Clear is hard-water stable, safe on plants, contains no dyes or fragrances and no hazardous acids such as HF/HCl/H3PO4.

Directions for Use

Clean-N-Clear is effective at ambient temperatures. However, it is normally used at 1 to 100% by volume of water at 70 °F to 210 °F for 5 seconds to 5 minutes. The parameters can vary due to the type and extent of soils to be removed. General window/building cleanup use at 1:50 (2% or 3 oz. per gallon of water - rinse with water. For spot removal use at 1:10 to full strength depending on the severity of the stains - rinse with water. For heavy stains use a pressure washer or scrub lightly with a sponge with a non-scratching surface.

Product Benefits

  • Contains no Silicates, HF, HCl or Phosphoric Acid
  • Environmentally friendly formula, biodegradable
  • Excellent foaming and residue-free rinsing properties
  • Effectively removes Type 1 Hard Water Stains/Spots

Physical Properties 

  • Use concentration (spray/squeegee): 1% (1:100)
  • Use concentration (floor scrubbers): 1% (1:100)
  • Use concentration (rust removal): 50-100% (1:1 - 1:0)
  • Bulk Density: 9.4 lbs/gal
  • Operating Temps: 70 °F to 210 °F
  • pH, Concentrate: 2.2 - 2.4
  • pH, @5%: 2.4 - 2.6
  • VOC (Concentrate): 0 g/L
  • Flash Point: None
  • Chelates: No 
  • Soluble in water : Complete
  • Biodegradable: Yes
  • Corrosive : No 

Availability: 5-gallon and 55-gallon containers, 275-gallon totes and bulk tankers.
Shipment: Non-regulated material, liquid
Storage: Keep out of direct sunlight. Keep from freezing. Store between 40 °F - 120 °F.
Disposal: Dispose of in accordance with local, state, and federal regulations. For assistance with disposal contact NuGeneration Technologies.
Regulatory: This product is classified and labeled according to the Globally Harmonized System (GHS).

EMERGENCY OVERVIEW

This product may cause irritation to the skin and eyes.

SAFETY

Please make sure you have read and understand the product label and SDS before using this product. Avoid breathing vapors, spray or mists. Use only with adequate ventilation. Wash thoroughly after handling. Observe label precautions. 

 


Removes Type 1 Water Stains/Spots
Contact Us