Bond-X Green - Product Guide
NUGENTEC BOND- X GREEN High Performance Cold Mix
NUGENTEC BOND-X GREEN High Performance Cold Patch is a high quality, pre-mixed, all
weather, permanent asphalt “cold patch” compound. Combining a carefully selected aggregate with a
special bitumen formula using a biodegradable, renewable, organic solution to replace petroleum
derivatives normally found in conventional cold mix asphalt. NUGENTEC BOND-X GREEN High
Performance Cold Patch is the right choice for all types of pavement repair jobs. BOND-X High
Performance Cold Patch repairs dangerous potholes, wide cracks, ruts, etc.; within minutes,
regardless of the weather outside. Suitable for use on both concrete and asphalt pavements.
NUGENTEC BOND-X GREEN High Performance Cold Patch is highly recommended for spot repairs
to driveways and dry pavement with no loss of bonding ability. The most important benefit to remember
is the fact the NUGENTEC BOND-X GREEN High Performance Cold Patch is the “Permanent Patch”
and should remain in the repaired area indefinitely. Money will be saved in labor cost because workers
will not be constantly repairing an area where a other types of “cold patch” asphalt mix was used.
NUGENTEC BOND-X GREEN High Performance Cold Patch is easy to apply with most repairs taking
only a few minutes to complete. As an added feature, NUGENTEC BOND-X GREEN High
Performance Cold Patch can be open to traffic immediately after it has been used.
PREPARATION: Simply sweep out the area to be repaired with a bristled brush or broom. It is a good
idea to remove any loose debris, dirt, ice, or standing water from the area to be repaired. This
action will promote good adhesion and bonding.
APPLICATION: No heating or mixing is required. Simply shovel into the pothole, crack, or rut, straight
from the container. If the fault is especially deep, i.e. over six inches, apply in two inch layers,
compacting each layer in succession. Shovel enough material into the fault to slightly crown the
“patch”. When completed compress the “patch” with the pneumatic tamper. Area can be opened to
traffic immediately.
COVERAGE: Depth and width of pothole, crack, utility cut etc. will greatly influence the coverage rate
achieved. As a rule however, forty pounds of NUGENTEC BOND-X GREEN High Performance
Cold Patch will fill a two inch deep hole, four square feet in size.
COLOR: Black
DRYING TIME: Immediate, following compacting of material.
CLEAN UP: All tools should be cleaned immediately after use with a solvent base cleaner such as
varsol, paint thinner or mineral spirits.
STORAGE: Always keep container tightly closed when not in use to prevent “hardening” over long
periods of storage.
PACKAGING: NUGENTEC BOND-X GREEN High Performance Cold Patch is available in five gallon
pails and 60# plastic bags.
DESCRIPTION: NuGenTec Bond-X Green High Performance Cold Mix is a permanent patch used to fill
potholes or construction openings in bituminous surfaces. This material is capable of being applied
in wet conditions where the temperature ranges from 15°F to 100°F. This material is stockpilable for
over one year when the asphalt and aggregate are manufactured by the prescribed method.
NuGenTec Bond-X Green contains less than 0.1% VOC by weight.
LIQUID ASPHALT: NuGenTec Bond-X Green High Performance Cold Mix liquid asphalt with chemical anti-stripping additives conforming to requirements of ASTM-D-1664 and ASTM-D-2027 modified as follows:
Flash Point: >400°F Minimum
Sybolt Furol Viscosity at 140°F: 200-500 SEC
Water: 0.2% Maximum
Distillate Test:
To 437°F: None
To 500°F: None
To 600°F: None
Residue at 680°F: 97%
Residue Tests:
Penetration at 77°F: 150-300
Ductility at 77°F: 100 cm Minimum
Solubility in trichloroethylene: 99% Minimum
AGGREGATE: NuGenTec Bond-X Green High Performance Cold Mix shall consist of crushed limestone or a submitted and approved by equivalent following under ASTM-C-136.
GRADATION ANALYSIS | CUMULATIVE PASSING |
3/8” | 90-100% |
#4 | 70-71% |
#8 | 37-38% |
#16 | 24-25% |
#30 | 15-16% |
#50 | 7-8% |
#100 | 4-5% |
#200 |