- Primary Application: vapor degreasing
- pH: n/a
- VOC: (g/L): 1310
- NFPA: 2,3,0
NuGeneration Technologies’ NuSolv™ D6368 is a stabilized n-Propyl Bromide formula used to remove solder fluxes, pastes, ionic residues, particulates, greases, resins, inks, silicone oils, buffing compounds, drawing oils and lapping compounds from a variety of surfaces including electronic and circuit assemblies, ferrous and non-ferrous alloys including Copper, Copper alloys (brass, bronze, etc.), Nickel, steel, stainless steel, Titanium, Zinc, and Aluminum., as well as a wide range of elastomers and plastics. NuSolv™ D6368 is hydrolytically stable in the presence of water contamination, which is a common problem in vapor degreasing. NuSolv™ D6368 conforms to Table 1 of ASTM D6368-06.
NuSolv™ D6368 was formulated to be used at both ambient temperatures for cold-cleaning/wipe applications as well as at elevated temperatures for vapor phase cleaning. NuSolv™ D6368 has very high solvency, with a Kb value of 130, making it a superior drop-in replacement for trichloroethylene (TCE), perchloroethylene (PCE), methylene chloride (MeCl), and expensive alternatives such as hydrofluorocarbons (HFC’s) and hydrofluoroethers (HFE’’s). NuSolv™ D6368 is a non-flammable solvent, and is SNAP approved due to its negligible impact on the ozone layer.
Directions for Use:
NuSolv™ D6368 is used at 100% concentration, and is effective at ambient temperatures in cold cleaning and wipe applications. However, it can also be used up to 71 °C (160 °F) for 5 seconds to 5 minutes for vapor phase cleaning. The parameters can vary due to the type and extent of soils to be removed.
- High-performance, environmentally-friendly solvent blend.
- Effective at ambient temperatures for cold-cleaning application, or at elevated temperatures for vapor-phase cleaning.
- Compatible with all metals and most elastomers and plastics.
|Physical Properties ||NuSolv™ D6368 |
|Use concentration (cold-cleaning/immersion) |
Use concentration (vapor phase)
|100% by volume |
100% by volume
|Bulk Density ||10.9 lbs/gal |
|Operating Temps ||Ambient to 71 °C |
|Boiling Point ||71 °C |
|pH, @100% ||N/A |
|VOC ||1310 g/L |
|Flash Point ||None |
|Cleaning Strength ||High |
|Ozone Impact (ODP) ||Zero |
|Global Warming Potential (GWP) ||0.3 |
|Kb Value ||129 |
|Vapor Pressure (mm Hg) ||139 |
|Regulatory Information ||VOC |
US EPA SNAP Approved
|Exposure Limit Information (ppm) ||18 ppm USEPA |
<10 ppm ACGIH
- To the best of our knowledge, this product is California Prop 65 compliant.
1-gallon, 5-gallon, 55-gallon, 275-gallon totes, and bulk tankers.Shipment:
Non-regulated material, liquidStorage:
Keep out of direct sunlight. Keep from freezing. Store between 40 °F - 120 °F.Disposal:
Dispose of in accordance with local, state, and federal regulations. For assistance with disposal contact NuGeneration Technologies at 888-99-NuGen or email: firstname.lastname@example.org.EMERGENCY OVERVIEW: May cause cancer. May damage fertility of the unborn child. Causes damage to organs. May cause damage to organs through prolonged or repeated exposure. Causes skin irritation. Causes serious eye irritation. May cause respiratory irritation. May cause drowsiness or dizziness.
SAFETY: Please make sure you have read and understand the product label and SDS before using this product. Avoid breathing vapors, spray or mists. Use only with adequate ventilation. Wash thoroughly after handling. Observe label precautions.
NuSolv 6368 nPB Based Precision Solvent n-Propyl Bromide conforms to Table 1 of ASTM D6368-06